Mirror, #4 Upgrade Module Kit, Explorer (Mirror, Plate, Screws, Tube)

Motor, X-axis & Y-axis for Gaia, GCC 29004139G        

Wheel, Half DU Roller Assembly (Gaia, X500-I)

LED's, Light Assy (Qty4) for: C180 (1&2), Explorer; Gaia (1&2)

For: C180-II & Spirit Model (Top X-axis Rail, Y-axis Inside Rail, BK01845A)

For: C180-II\Spirit Models, Pack of 2 (X-axis Bottom, BK01836A)

Sensor, PCB Board, X-axis Motor, For C180-I (4-Amp, MCB-5206, Replaces 29004513G & 23800235G)

AAASII Carriage Board Assembly for Expert 24LX  / Expert II 24LX  / Puma III

Pointer, Red Pointer Diode For GCC Lasers (Mercury, Venus, Jupiter, R)

PCB, Y-axis PCB C180-I & II

For: GCC Puma III

29004692G- Control panel Assembly for Puma III

Mirror 4, 1" Dia, Carriage Mirror Rev.2 for SGX/C180/GLS/SGLSHYB-Co2/SLS, SI/SGE > After SN: I50790, Mercuy III, MG380Hybrid, X252, X380 SN After SN U90xxx/T90xxx, Venus II SN start from T5619
Base Dims: 1.1" x 1.3" (28x33mm)

Lens, 4" FD for Spirit Models

Machine Model: Spirit Si \ SGE-After I50790, SGX, SGLS, SLS, C180-I & II  with .012" Spot Size, Rev. 2 

GCC Lens, 2" FD-Blue Rev. 2, Std Co2 Model Lasers (Not Fiber Hybrids)

Co2 Machine Models: Spirit SGX / SLS / SGLS / SGLSHYB-Co2 / C180-I / C180-II (Spirit Si/SGE machines with SN: After I50790+), Dim's: W=1.1"(28mm) x H=1" (25mm)

(Same as 29004737G)

GCC Machine Models:

Spirit Si\SGE\SGX\SLS\SGLS\C180-I & II (For machines with SN: After I50790+) 

Mercury III, MG380Hybrid, X252, X380 (For machines with SN: After U90xxx/T90xxx+)

For Spirit GX & Spirit GLS with Serial # Before: N52181

GCC-29004998G Lens, 2.5" FD-Gold

Machine Models:  Spirit  (SI, SGE, SGX, C180) with .007" Spot Size, Rev.2

(Without Focus Tool # LGCC-29002606.0 $26, Mach. After SN: I50790)

Board Notes: DC 12VC PCB for Laser Tube Fans

Machine Models: Spirit /Gaia/X500

Roller, DU Roller Assembly-Top X-axis EACH (Gaia, X500-I)

PCB, Auto Focus PCB, For Flat Cable, Rev. 2, After SN: N95617 (SLS\SGLS\C180-II, Mercury III, X380, X252)

Motor, Z-axis, Assembly (C180-I & II)

MCB, GCC Main Mother Board (Mercury II, New MCB) 6 Month Warranty
* eMail and ask if a Refurbished MCB is available, click here.

29005210G  Carrier guide roller  Assembly For Puma I-III  (DU type) 

GCC-29005238G Rail, X-axis Linear Guide (S290)  with Rail, belt, lens carriage

 Includes:

22800923G, X-axis slideway
22800928G, Tension pulley shaft
29002533G, Tension idle pulley Assy
20700053G, Bearing (687ZZ)
29002539G, X-axis transmit shaft Assy
290105180G, XY Motor Assembly
20600076G, X motor belt (2GT-T90-10)
29002540G, X-axis Transmission pulley Assy
20600074G, X-axis Open Belt (2GT*T895*W12)
29005888G, Lens carriage Assembly
23300310G, X Tube Chain
20901519G, Flat cable 1.0mm 8pin(1220mm)
29002601G,Air Assist Tube 1100mm
290101080G, X Motor PCB, 5A
20901688G, PCB TO AUTO FOCUS CABLE

29005256G - Watch Dog-Interface Converter Board Assembly, Jaguar II/III/IV (no watch dog for J5 series)

The Watchdog is usually located on the side of the machine, where the white ribbon cable connects, the control panel and motor run through it.

Panel, Control Panel Board Assembly (LMC-STC2A20DRG-011)
For: Jaguar II,III,IV/Pume II, III/VOGUE/Expert Pro

29005344G -GCC  Watch dog board Assembly for Puma III

GCC-Coverlid, Top Green PV Lid for S290 Fiber Laser 780-1400nm (Window ONLY- NO hinges)

Sensor, AAS II Sensor Assembly w/Bracket for Puma III

29005383G- GCC 2 in 1 Cutter mainboard with Puma II firmware (for Service)

Mirror, #2 or 3, 0.75" Diam. (S290 Spirit Fiber After Serial#: H50246>)

Motor, X-axis (C180-I) with 3-Months Manufacturer's Warranty (Hansen Motor 116-32624-8)

Motor, X & Y-axis C180-II & C180-I, E200, Hansen Motor # 116-33224-8  with 3-Months Manufacturer's Warranty

Pointer, Red Pointer Diode For GCC Lasers (C180-I & C180-II)

For: GCC Models Spirit SLS\S290LS (Before Serial #: I50790)

Motor, Roll-To-Roll Stepping Motor Assy

Control Panel Assembly, Expert-24

GCC 29005951G Holder, Ball Point Pen Holder Assembly w/Package

29005962G, Roller Holder without Damper, Jaguar 101/ RX-101  (Length 49.6" / 126cm)

Pin, Auto Focus Pin Assembly for X380 & MG380-HYB (8.5" Cable)

For Models Spirit Si & SGE After Serial #: I50790

Rail, X-axis Linear Guide with Bearing Block Assembly (Spirit LS, X-axis PCB 5a, 5272MB)

Includes: Linear rail and bearing block, Auto Focus Pin, wire-hardness with the track, bearings along with assisted air hose

GCC 29006052G Holder, Blade Holder for Jaguar 1-4/Puma 1-3/BN/SB/BI/EX I/EP(2.0mm)

Carriage Assembly without PCB(EX-24 LX) for GCC Expert 24

29006194G Roller, Pinch Roller Assembly, RX &RXII

Switch, Limit Lever for Z-axis Table

Rail, X-axis Linear Guide with Bearing Block, PCB(5A) for 5272 MB (Spirit SGLS/Hybr)

Includes: Linear rail and bearing block, Auto Focus Pin, wire-hardness with the track, Mirror #4, bearings along with assisted air hose

* We require confirmation of Machine Serial # to match electronics
** ETD: 1-2 Weeks, call for availability 

GCC 29006425G Lens, 4" FD, Spirit Fiber S290LS

For Machines After Serial # I50790 and GLS Hybrid Fiber Only