Shear, Guillotine Shear 13", Model 3001/13
The 3001 Guillotine Shear was originally designed in 1999. The original prototype was a 13" shear and continues in use. While the basic design of the 3001 shears has remained unchanged since that original prototype, the shears have continued to evolve with changes made as appropriate. Three 3001 shears are available; a lighter duty 13" and the standard 13" and 25".
The 3001EVO/13 is the lighter duty version of the original 13" shear and is discussed at the bottom of the page. The standard 13" and 25" shears (3001/13 & 3001/25) have been upgraded with 1/2" thick end plates, heavy duty alignment blocks for the upper blade holder with 1/4" thick aluminum bronze wear plates, and a new drop off/rear gauge. In addition, all of the shears have the Standard Features listed below.
The standard 13" & 25" shears are constructed to industrial standards, and the resulting mass of the shears contributes significantly to their performance. If you have worked with industrial equipment, you know that the heavier, sturdier equipment is more stable and less fatiguing to operate. Depending on the size, the shears weigh from 85 to 150 pounds. Most of the weight is in the guillotine action that is made entirely of steel. Once that mass is put in motion, its inertial contributes to the ease and smoothness of the operation of the shear. While lighter weight designs can move during use and be difficult to use, the standard 13" & 25" shears do not have these problems. The shears cut foils, aluminum and plastic with little or no effort. Even the most timid operator can cut harder materials like half-hard trophy brass producing full width cuts that are flat and square.
* * * * *
Model 3001 Standard Features:
“Flip-Up Hold-Down”
Exclusive “Flip-Up Hold-Down” is standard on all standard 3001 shears. When in the down position, it automatically applies pressure to the material to facilitate smooth, accurate cutting. When necessary, the hold-down may be flipped up out of the way to permit easy access to the blades.
Movable Handle
The shear handle may be installed on the left or right of the shear enabling right handed and left handed operators to use the same shear.
Precision Drop-Off Bar
The Precision Drop-Off Bar is full width and is an invaluable aid for making accurate, repetitive cuts. It is mounted to the top blade carrier and moves up and down with the top blade like the rear gauge on many larger guillotine shears. It is above the material and doesn't interfere with the material as it falls away from the shear after it is cut. It slides on two alignment rods and is locked in position by turning a knob on each rod.
Step Ruler
The typical ruler is a stamped piece of thin metal. The ruler is machined from a thick, solid piece of steel. There are six separate steps involved in its manufacture with the last being a precision grinding of the front edge to insure that the ruler is straight and true. Because of its thickness, it is very stable, and the edge will not lift or distort allowing material to slide underneath the ruler. Lastly, the ruler is stepped to place the measuring edge close to the work surface for easier reading. The ruler is graduated in 1/16th's of an inch.
Blade Adjustment
The standard 3001 uses the same blade system pioneered on its 2001 Bench Shear. The blades are mounted with tapped bolts rather than the old fashion nut and bolt system, and the bottom blade is adjusted with set screws instead of eccentrics. A much safer, quicker and simpler method of installing and adjusting the blades.
Shear Capacity:
· Aluminum................................................. .040"
· Brass........................................................ .025"
· Flexible Plastic........................................... .125"
· Brass Plated Steel....................................... .025"
Size & Weight:
· 3001/13 - 26"L x 20"W x 12.5"H (W/out handle); Approximately 85 lbs.
· 3001/25 - 26"L x 32"W x 12.5"H (W/out handle); Approximately 150 lbs.
Availability & Ordering
The 3001 is built to order. Please check for current availability and delivery. At the time of ordering it is necessary to specify which type of blade you prefer. The choices are either for metal or, for plastic. The 13" is also available with a multi-purpose blade. If you are unsure which blade will be best for you, call us to discuss your choice.