FOR SUPPORT:  HELPDESK TICKET FORM

Belt, Y-axis Motor Belt, Short-Closed, For: Spirit Si\GX\GE, S290 (186-2GT-10)

Belt, X-axis Carriage Belt, Long-Open, For: Spirit GE  (2GT-2370-12, 93.3"L)

Y-axis belt (S2M-W9-T774) Expert-24

Belt, Y-axis belt (S2M-W9-T774) Expert-24

GCC 20600107G Belt, X Axis Carriage Belt, Long-Open for: X500 & Gaia (2GT-3200-20)

Belt, Z-axis For: C180-I & II (2115-5GT-9)

Belt, Y-Axis Carriage Belt (2GT-L1600-W12)  X-380, ~ 63.75"

Belt, X-axis Carriage Belt, Long-Open (2GT-2430-10, X-380, 95.6"L)

Belt, X & Y Axis Motor Belt, Short-Closed, For Spirit LS, SGLS, SGLS-HYB, X500-II (FHT-2*T90*W10)

Belt, Y-axis Carriage Belt, Long-Open 51.5" (131cm), For: Spirit LS / S290LS, After SN: K50114

X-axis Open Kevlar Belt (FHT-2*T897*W15)

For: GCC Spirit LS, belt only

Belt, X-axis  Motor kevlar Belt, Short-Closed. for: X500-II (FTH-2" L150  W6)  206001840G

Belt, X-axis Carriage Belt, Long-Open (2GT-2430-10, X-380, 95.6"L)

For: Spirit Si, SGX, Explorer

Cable, Laser to MCB BNC Cable, Mercury/GAIA I/II Laser (CN00178)

20900376  Flat Cable for Lynx 30 60 / Puma I 30 60  8 pin

Cable, X-Motor Flat Ribbon (Explorer/Venus/R, 41.5" L)

Cable, X-Motor Flat Ribbon, 12 Pin, 70.8"L-180mm (X500-II)

Cable, Flat Cable, 16-pin, 1010mm, Puma II 30 & 60/Bobcat/Bengal (PC00123) 

Cable, Control Panel to MCB, 10-Pin, 95cm (Explorer)

Cable, Fan PCB DC output to 12V PCB cable 1700mm (0116-9091-173-1) Spirit GX

Cable, LED Lamp Cable to DC12V – 160cm (0116-257-164) For: Spirit GE,GX, GLS

Cable, MCB to Laser Board on GAIA I/II Laser (RCA to RCA)

Cable, USB Cable, Communication, Machine Frame Port, B type Cable MOLEX 5Pin 2.54mm, 40cm (Mercury II & III/C180 with 5206E and 5272 earlier V1 MB)

Cable, Control Panel to MCB, L:59cm (Mercury II/III)

Cable, USB Cable, Communication, Machine Frame Port, B type Cable MOLEX 5Pin 2.54mm, 40+cm (X380-MG380, \MCB 5206E & early 5272V1)

 GCC 20901614G Cable, Control Panel to MCB,  For: C180-II

Cable, Laser Tube Power Cable Glass Tube  209021580G

Cable, Fan PCB DC output to 12V PCB cable 1700mm (0116-9091-173-1) Spirit GX

Cable, Rotary Connection Cable from Machine to Attachment PCB (155cm for Rotary Assy 29001051G and 290072190G)

GCC-209027610G Cable, Laser Tube Signal Cable, 80GT, 1730mm to MCB

Bypass Connector Plug for Pass-Through Door Switch Module For GCC 2019+ Models: Mercury III/Spirit/Spirit LS/GLS/GLS Hybrid/X252EX/X380RX/X500III/MG380Hybrid/S400

GCC-209031800G, Cable, Flat Flexible (FFC) Pitch:1.0mm 15pin 110cm

Model: E200

Connector, Laser Housing D-SUB Male 15pin to BNC Connector  (SY003-340(LF)) - BNC Cable to T60, Gaia II, MIII, Si, SGE, SGX, SLS, SGLS

Adapter, for Synrad Laser Ti Series, Laser Housing D-SUB Male 15pin to RJ45 Connector 

21500021G  Flash ROM (DIP) (A290021T-70F) for Puma

Ring, Depth Noze-Metal (Thick) For: EGX300\EGX350\EGX400\600\ZDN-200

Micrometer, Ring Dial Set-Spindle for EGX400/600

GCC-216000980G Raspberry Pi 3 Module B+

Model: E200

Bearing, R-Bearing, 6801ZZCMP5NS7L For Roland EGX-360, MDX-40

Nose Cone Adapter, (M) Standard EGX-20

This Standard Adapter Nose (Product #21905162) is used in the EGX-20. The nose protects materials from scratching when using the Auto-V function. This nose is designed to accommodate smaller sized tools.

Wrench, EGX-350 Spanner Wrench Tool (2 sided)

* This Tool Spanner (Product #21935111) is used to install and tighten collets within the spindle. This spanner is intended for use with the EGX-350 and EGX-400/600 engravers.

Wrench, Tool Spanner 6-14 CS-20/EGX-30/EGX30a/EGX20

* This Tool Spanner (Product #21935115) is used to install and tighten collets within the spindle. This spanner is intended for use with the EGX-20 engraver.

Wire, X-Axis CS-20 EGX30 (ea, 1 on Machine)

Wire, Y-Axis CS-20, EGX30 (ea., 2 on Machine)

Wire, X-Axis PNC2300A\EGX300

 Right & Left Side, 74"/188cm